Panel Upgrade for EV Charging in Longview, TX
A panel upgrade for EV charging replaces an older or full electrical panel, often 100 amps, with a larger one, usually 200 amps. You need it when a load calculation shows your home cannot handle a charger on top of its other big appliances. Some homes can avoid a full upgrade with a smaller charger setting or load management.
Not sure if your Longview home needs one? Call to get connected with a local electrician who can check.
How do you know if you need a panel upgrade?
You likely need a panel upgrade if your panel is 100 amps or less, has no open breaker spaces, or the load calculation shows too little capacity left. Signs also include breakers that trip often and lights that dim when big appliances start.
- Main breaker is 100 amps or less
- No empty slots for a 2-pole breaker
- Panel is very old or an outdated brand
- Lights flicker when the AC kicks on
- Breakers feel warm or show scorch marks
What is a load calculation?
A load calculation adds up what your home uses (AC, water heater, range, dryer, and more) and compares it to your panel's capacity. It shows whether there is room for a 40 or 50-amp EV circuit. It is the step that decides whether you need an upgrade, so ask for it before paying for one.
Need help with panel upgrade for EV charging?
Call (903) 532-7482Are there options besides a full panel upgrade?
| Option | How it helps |
|---|---|
| Lower charger setting | 16 to 24 amps can still refill most daily driving overnight |
| Load management device | Pauses charging when the house uses a lot of power |
| Smart charger with load sharing | Adjusts charging to match available capacity |
| Circuit sharing switch | Shares a dryer circuit so both never run at once |
What happens during a panel upgrade?
- Load calculation and permit.
- The utility is scheduled to disconnect power.
- Old panel is removed and the new one installed.
- Circuits are moved over and labeled.
- EV circuit is added.
- City inspection, then power is restored.
Most upgrades take a full day. Your power is off during the swap.
100-amp vs. 200-amp panels for EV charging
| 100-amp panel | 200-amp panel | |
|---|---|---|
| Common in | Older homes | Newer and upgraded homes |
| Room for a 40 – 50 A EV circuit | Often tight with central AC and electric appliances | Usually yes |
| Two EVs | Needs load management | Often possible |
| Future add-ons (heat pump, hot tub) | Limited | Plenty of room |
What is load management for EV charging?
Load management watches how much power your home is using and slows or pauses EV charging when the house is busy, such as when the AC, dryer, and oven run together. It lets you add a charger to a panel that would otherwise be too small. Some smart chargers do this with a current sensor; others use a separate device. It is often a fraction of the cost of a full upgrade.
Signs your panel needs attention beyond EV charging
- Fuses instead of breakers
- Rust, water stains, or corrosion inside the panel
- Breakers that feel warm or buzz
- Double-tapped breakers (two wires on one screw)
- A panel brand an inspector flagged during a home sale
If any of these apply, fixing the panel is a safety step on its own, not just an EV upgrade.
Who handles the permit and SWEPCO for a panel upgrade?
The electrician usually pulls the city permit and coordinates the power disconnect and reconnect with the utility. For many Longview homes that is SWEPCO; some outer areas use a rural co-op. If the meter base or service line also needs upgrading, the utility may need to schedule its own work, which can add days. Ask your electrician for a timeline that includes permit, utility scheduling, and inspection, not just install day.
Panel Upgrade for EV Charging near Longview
Local electricians on our line serve these areas.
How long does a panel upgrade take?
The work itself usually takes one day. Scheduling the utility disconnect, permit, and inspection can stretch the full process to one to three weeks.
Can I charge an EV on a 100-amp panel?
Sometimes. Many homes with 100-amp panels can charge at a lower setting, especially with gas appliances. A load calculation will tell you. Load management devices can also make it work without an upgrade.
Does a panel upgrade raise home value?
It can help. Buyers with EVs look for homes that can charge, and a newer panel is a plus during inspections. Exact value depends on the home and the market.
Will the power company need to be involved?
Yes, for a full panel swap. The utility usually disconnects and reconnects power, and may need to upgrade the service line or meter. The electrician typically coordinates this.
Is a 150-amp panel enough for an EV?
Often yes, depending on your other loads. Many homes with 150 amps can add a 40-amp charger, especially with gas heat or water heating. A load calculation confirms it.
Do I need a panel upgrade for a Tesla Wall Connector?
Not always. The Wall Connector can be set to a lower current to fit your panel's spare capacity. Tesla's power-sharing features can also help two-EV homes avoid an upgrade.
Related services
EV Charger Installation
New Level 2 charger installs with a dedicated circuit, sized for your panel.
View service →Breaker Tripping Repair
Find out why your EV charger keeps tripping the breaker and fix the cause.
View service →Level 2 Charger Repair
Fix home 240V chargers that won't start, stop mid-charge, or show error lights.
View service →Need panel upgrade for EV charging today?
Call to reach a local electrician serving Longview, TX.